1.加工前先檢查設備運行情況，待正常后再加工。
　　1. Check the operation of the equipment before processing, and then reprocess after normal processing.
　　2.加工的物料應符合要求，防止發生超負荷運行事故。
　　2. Processing materials should meet the requirements to prevent overload accidents.
　　3.加工過程中，操作人員應避開切刀的危險部位和裸露的傳動部位。
　　3. In the process of processing, the operator should avoid the dangerous parts of the cutter and the exposed driving parts.
　　4.設備運行過程中，發生堵塞、停止運行等故障或者需人工轉動皮帶傳動部分（盤車）時；必須切斷電源，然后再處理。
　　4. In the process of equipment operation, when blockage, stop operation and other faults occur or the belt drive part (turning) needs to be manually rotated, the power supply must be cut off and then processed.
　　5.加工完成后，及時切斷電源；設備清洗干凈，保持清潔衛生。
　　5. Cut off the power supply in time after the processing is completed; the equipment is cleaned and kept clean and hygienic.
　　一、日常保養
　　Daily Maintenance
　　1、保證零部件整體性好。在操作的過程中保證儀器每一個部件鎖緊，不要有松動。如果有松動，不僅不能切出滿意的切片，同時也對儀器損傷很大；保證切片的一定角度。在調好該切片機的zui佳角度后，盡量不要隨意調動角度，否則難以切出理想切片或出現跳片現象。
　　1. Guarantee good integrality of parts and components. In the process of operation, ensure that every part of the instrument is locked and not loosened. If there is loosening, not only can not cut satisfactory slices, but also damage the instrument greatly; ensure a certain angle of slices. After adjusting the Zui angle of the microtome, try not to adjust the angle at will, otherwise it is difficult to cut the ideal slice or appear the phenomenon of jumping slice.
　　2、盡量少移動刀架和刀架上的部件。因?yàn)樗鼈兌际墙?jīng)過固定卡丁固定在一起的，如果經常移動會造成卡丁和卡槽之間磨損，容易松動或卡不牢，給切片造成困難。
　　2. Move the parts on the tool holder and tool holder as little as possible. Because they are fixed together by fixed karting, frequent movement will cause wear and tear between the karting and the slot, easy to loosen or stuck, causing difficulties for slicing.
　　3、保持切片機的清潔。在每次用完后，徹底清掃切片機上的蠟片及蠟屑，然后用機油擦拭表面，以免交叉污染和影響刀架的壽命。
　　3. Keep the slicer clean. After each use, thoroughly clean the wax and wax debris on the slicer, and then wipe the surface with oil to avoid cross-contamination and affect the life of the tool holder.

                              
　　4、保證室內環境的干燥及清潔，每種精密儀器都有其適應的環境及空氣酸堿度條件，如果空氣比較潮濕，儀器就容易生銹、生成氧化膜等現象，而且每次使用切片機的時候，都要用冰塊凍蠟塊，切片機旁邊有溫水漂片，這些都會影響空氣濕度。所以在切片時應配備干燥儀器或空調。
　　4. To ensure the dryness and cleanliness of the indoor environment, each precision instrument has its own suitable environment and air acidity and alkalinity conditions. If the air is humid, the instrument will easily rust and form oxide film, and every time the slicer is used, it will use ice-frozen wax blocks, beside the slicer there are warm water drifting slices, which will affect the air humidity. Therefore, when slicing, drying instruments or air conditioning should be equipped to dehumidify.
　　二、日常維護
　　II. Daily Maintenance
　　每天使用之前要仔細檢查切片機各個部件是否正常，用完之后各部件調到原位。要注意按步驟開關機，發現異常盡快維護及修理，以免發展為儀器故障。對于儀器故障，我們應仔細觀察、分析，簡單故障盡量自己排除，對于復雜的故障要請維修人員，并在工程師維修時做好維修記錄，總結經驗，以利于以后對儀器更好地保養和維修。
　　Before using it every day, we should carefully check whether the parts of the slicer are normal or not. After using it, the parts are put in place. Pay attention to switch the machine step by step, find abnormal maintenance and repair as soon as possible, so as not to develop into instrument failure. For instrument failure, we should observe and analyze carefully, eliminate simple failure as far as possible, ask professional maintenance personnel for complex failure, and make maintenance records when engineers repair, summarize experience, in order to facilitate better maintenance and maintenance of the instrument in the future.
　　如果出現馬達推進、后退及切片進度不正常故障（故障是線路老化引起），打開機蓋后發現切片機線路板有些生銹且灰塵很多。所以在有可能的情況下，機身內線路板要定期維護，用100%乙醇擦拭，線路板插口用橡皮擦擦除表面氧化膜嗎，這樣可以延長線路板壽命。
　　If there are abnormal faults of motor propulsion, backward and slicing progress (the fault is caused by the aging of the circuit), after opening the cover, it is found that the circuit board of the slicer is rusty and dusty. So if possible, the PCB in the fuselage should be maintained regularly, wiped with 100% ethanol and erased with eraser on the PCB socket, so as to prolong the life of PCB.