全國咨詢熱線
生產能力：800/1200 kg/h 電機功率：1.5 kW 切菜規格：800/1200 kg/h 尺寸：1300×600×1050 mm/1800×710×103
yqc系列切菜機是模擬手工切菜原理，采用“無級調速”和“離心式切片機構”等---技術研制而成的復合式多功能切菜機。適用于各種根，莖，葉類蔬菜和海帶的加工，也是醬菜行業必不可少的理想設備之一.
Yqc series vegetable cutter is a kind of compound multi-functional vegetable cutter, which simulates the principle of manual cutting and adopts the technology of "stepless speed regulation" and "centrifugal slicing mechanism". It is suitable for processing all kinds of root, stem, leaf vegetables and kelp
1.調換不同的刀 具可把瓜薯類蔬菜切成片，絲，丁，曲線，菱形。
1. Change different knives to cut melon and potato vegetables into slices, silk, dice, curve and diamond.
2.還可把細長類蔬菜（韭菜，豆角等）切成段，以及把葉類蔬菜切成絲。
2. You can also cut slender vegetables (leeks, beans, etc.) into sections, and cut leafy vegetables into shreds.
3.菜的長短厚薄可調。安裝調試1.將機器放在水平的工作場地，---機器放置平穩---。
3. The length and thickness of the dish can be adjusted. Installation and debugging 1. Put the machine in a horizontal work site --- the machine is placed stably.
4.使用前對各部位進行檢查，緊固件是否在運輸途中松動，開關及電源線是否因運輸而破損，并及時采取相應措施。
4. Check all parts before use to see if the fasteners are loose during transportation, and if the switch and power cord are damaged due to transportation, and take corresponding measures in time.
5.檢查旋轉料筒內或輸送帶上是否有異物，如有異物必 須清理干凈，以免引起刀 具損壞
5. Check whether there are foreign matters in the rotating barrel or on the conveyor belt. If there are foreign matters, they must be cleaned to avoid tool damage
6.確定電源電壓與本機額定電壓相符合。在外地接地，記處---接地，將電源軟線伸長找電工將機器電源線接在全 極斷開大開距電源上，接通電源，按下“on”按鈕，檢查轉向，v帶輪的轉向與表示一致為正確。否則，切斷電源，調整接線。
6. Make sure that the power supply voltage is consistent with the rated voltage of the machine. In the field of grounding, note - grounding, the power cord extension, find electrician to connect the machine power cord to the full pole off large distance power supply, turn on the power, press the "on" button, check the steering, V pulley steering is consistent with the expression is correct. Otherwise, cut off the power supply and adjust the wiring.
使用操作
Operation
1.工作前先試切，觀察所切蔬菜規格與要求規格是否一致,否則應調節切片厚度或切菜長度，符合要求后進行正常工作。
1. Try to cut the vegetables before work, and observe whether the specifications of the vegetables are consistent with the requirements. Otherwise, adjust the slice thickness or cutting length, and work normally after meeting the requirements.
2.安裝豎刀2.1智能切菜機安裝豎刀：把豎刀放在定刀板上，刃口與定刀板下端平行接觸，定刀板銷在刀架上，緊固切刀螺母，拆下定刀板即可。
2. Installation of vertical knife 2.1 installation of vertical knife for intelligent vegetable cutter: place the vertical knife on the fixed knife plate, the edge is in parallel contact with the lower end of the fixed knife plate, the fixed knife plate pin is on the tool holder, fasten the cutter nut, and then remove the fixed knife plate.
3其他切菜機安裝豎刀：先轉動可調偏心輪，使刀架行下死點后，再使刀架向上抬起1/2毫米，使豎刀與輸送帶接觸后，緊固螺母把豎刀緊固在刀架上。說明：高架抬起高度可根據所切蔬菜自行掌握。如果高架抬起高度小，蔬菜有可能連刀，如果高架抬起高度過大，有可能切壞輸送帶。
Installation of vertical knife for other vegetable cutters: first turn the adjustable eccentric wheel to make the knife rest move to the bottom dead point, then lift the knife rest up 1 / 2 mm to make the vertical knife contact with the conveyor belt, and fasten the vertical knife on the knife rest with the fastening nut. Note: the elevated height can be controlled according to the cut vegetables. If the lifting height of the viaduct is small, the vegetables may be cut. If the lifting height of the viaduct is too high, the conveyor belt may be cut.
4切菜長度調整：觀察控制面板上顯示的長度數值與要求長度是否相符，增加長度時按增長按鈕，減小長度時按減小按鈕。其他切菜機調整：轉動可調偏心輪，松開連桿緊固螺釘，切細絲可移動支點，由外向里；切粗絲時可移動支點，由里向外，調好后緊固調整螺釘
4 cutting length adjustment: observe whether the length value displayed on the control panel is consistent with the required length, press the increase button when increasing the length, and press the decrease button when decreasing the length. Adjustment of other choppers: turn the adjustable eccentric wheel, loosen the connecting rod fastening screw, cut the filaments, and move the fulcrum from the outside to the inside; When cutting thick wire, the fulcrum can be moved from inside to outside, and the adjusting screw can be tightened after adjustment